This angular gear is delivered without a motor and is suitable for a wide variety of applications. Due to its compact design, robust drives can also be implemented in larger models. Whether as a drive unit for 1:43 or larger, as a chain drive, anchor or cable winch, the Easy universal gear unit impresses with its compact design.

The kit is supplied with detailed instructions. So it can be easily modified for your own ideas. If, for example, the drive axle is shortened and only led out on one side, powerful winches can be built or, in a larger vehicle, each wheel can be driven by its own motor, which saves the differential.

Application examples: The set can be combined with all metal gears from our G50 - G1000 series, in 6 or 12 volts. This means that all revolutions from 4 to 400 rpm can be generated. Drive for 1:43, powerful winches, chain drives and special functions are just a few possibilities that this gearbox offers.

Mounting accessories: screwdriver, watchmaker's screwdriver

Weight : 14,5 gr

 [ BUILDING INSTRUCTIONS - 394 Ko ]

This open, inexpensive angular gear with the G50, 6 volt gear unit is ideal as a drive unit for 1:43 or 1:50 models. The complete gearbox is screwed on, which makes assembly and maintenance easier.
The gearbox is supplied as a kit with detailed instructions. So it can be easily modified for your own ideas.

Application examples: Drive for 1:43, powerful winches, chain drives, special functions.

Voltage range 2-6 volts

Mounting accessories: screwdriver, watchmaker's screwdriver

 [ BUILDING INSTRUCTIONS - 261 Ko ]

This engine is characterized by best start-up characteristics. Already at just over 0.1 V, the engine starts powerfully. The 5-pole version reduces the maximum speed and increases the torque. The engine thus generates power at low speeds and is therefore ideally suited for micro-gearbox construction and all about movement in 1:87 model making.

TECHNICAL SPECIFICATIONS:

• Axle diameter: 0.8 mm
• Axle length: 5 mm
• Length o. Axis: 16.6 mm
• Cable length: 20 cm
• Voltage: 0.1 - 5.0V
• U / m: 14500 @ 5V

 [ DATA SHEET - 1,46 Mo ]  

This engine is characterized by best start-up characteristics. Already at just over 0.1 V, the engine starts powerfully. The 5-pole version reduces the maximum speed and increases the torque. The engine thus generates power at low speeds and is therefore ideally suited for micro-gearbox construction and all about movement in 1:87 model making.

TECHNICAL SPECIFICATIONS:

• Axle diameter: 1 mm
• Axle length: 5 mm
• Length o. Axis: 16.6 mm
• Cable length: 20 cm
• Voltage: 0.1 - 5.0V
• U / m: 14500 @ 5V

 [ DATA SHEET - 1,46 Mo ]  

With the "RSL Compact" the serial PPM signal of an RC receiver is evaluated and a complete model is controlled. 3 speed controllers, 4 servos and the complete lighting system including all-round lights and front flashers are available. The module does not have to be configured. All functions are available after soldering to the soldering pads concerned. The assignment to the channels is also already configured.

TECHNICAL SPECIFICATIONS:

• Dimensions: 15.3 x 10.5 mm
• Weight: 0.7 grams
• Supply voltage: 3.3 - 5.5 V DC voltage
• Load capacity: maximum 2A over the entire module
• Incoming protocols: PPM 6 channel
• Speed ​​controller: 3 pieces each 800 mA (300 Hz)
• Switching outputs: 10 pieces, 10 mA each

The 2.4 GHz receiver R614XN is also included in this set:
With the R614XN we have a small 6 channel receiver in the DSM2 / DSMx protocol. The connections are brought out as solder pads and allow easy wiring despite the small dimensions. Ideal for small vehicle models, ships and indoor planes.

TECHNICAL SPECIFICATIONS:

• Protocol: DSMx / DSM2
• Channels: 6 channels plus cPPM sum signal
• Weight: 0.5 g
• Operating voltage: 3.7 to 9.6V
• Dimensions: 11.7 x 11.7 x 3 mm

With the "RSL Compact" the serial PPM signal of an RC receiver is evaluated and a complete model is controlled. 3 speed controllers, 4 servos and the complete lighting system including all-round lights and front flashers are available. The module does not have to be configured. All functions are available after soldering to the soldering pads concerned. The assignment to the channels is also already configured.

TECHNICAL SPECIFICATIONS:

• Dimensions: 15.3 x 10.5 mm
• Weight: 0.7 grams
• Supply voltage: 3.3 - 5.5 V DC voltage
• Load capacity: maximum 2 A over the entire module
• Incoming protocols: PPM 6 channel
• Speed ​​controller: 3 pieces each 800 mA (300 Hz)
• Switching outputs: 10 pieces, 10 mA each

Speed controller ERMIKRO, bidirectional, 800 mA continuous current.
Measuring only 8.45 x 5.5 mm, this speed controller can control motors with up to 800 mA in two directions (forward/reverse). This makes it ideal for use in small and very small models. The ERMIKRO has outputs that control reversing lights and brake lights. If the accelerator is suddenly released, the brake light illuminates briefly. If the motor reverses, the reversing lights illuminate. If the standby input is activated and connected with the minus, the controller switches to standby.
For safety reasons, the throttle stick must be in neutral at the time of standby activation to prevent sudden restart. This function is very well suited for securing a construction vehicle during transport on a low-loader against unintentional movement or rolling away. In the case of small functional models, special functions can also be selectively switched on and off. A digger, for example, can be switched between both the digger and driving functions. Our two-channel switch (2KM) or a suitably configured P output of a delta receiver (e.g. RX43, RX47, RX45) is suitable for control.

TECHNICAL SPECIFICATIONS:

• Operating voltage in V: 2,7 - 5
• Motor current duration in mA: 800
• Motor current pulse in mA: 1200
• Dimensions: 8.45 x 5.5 mm
• Clock frequency: 300 Hz
• Output for brake light: 30 mA max
• Output for reversing light: 30 mA max

 [ DATA SHEET - 1,48 Mo ]  

These bevel gears fit perfectly on all our metal gears with a 3 mm shaft.
To build angular drives, bevel gears have unbeatable advantages. In contrast to worm drives, they are not inhibitory and have a better efficiency.
For use in micro model making, we have a bevel gear with an outside diameter of just under 8.2 mm in our range.
Be it as an axle gear, for cable winches or individual gear solutions, this gear can be used to find interesting solutions not only in micromodel construction.

TECHNICAL SPECIFICATIONS:

• Set consisting of 2 bevel gears
• Material: brass
• Module: 0.5
• Number of teeth: 15
• Head circle / outside diameter: 8.2
• Pitch circle: 7.5 mm
• Bore: 3.0 mm
• Bundle: Ø 5.8 mm / height: 4.9 mm

[ Dimensions - 128 Ko ]

Anyone looking for a powerful universal drive will find it here.
The output axis of the UNIVERSALANTRIEB POWER has ball bearings and the housing is milled from brass. The complete gearbox is screwed, which simplifies assembly and maintenance. Even when assembled, the gear cover can be removed for maintenance.
The gearbox is supplied as a kit with detailed instructions. This makes it easy to modify for your own ideas. E.g. the drive axle is only led out on one side, powerful winches can be built or each wheel on a larger vehicle can be driven by its own motor, which saves the differential.

In the "Power Plus" set, everyone can order the gearbox that suits their purposes. Simply choose the desired voltage from our metal gears and choose the optimum speed for the application. The voltage is variable from 0.3 - 6 volts or 2 - 18 volts. The universal gearbox is therefore not only suitable for model builders, but also in particular for a wide variety of tasks in railway model construction.

Application examples: drive of trucks 1:43 and 1:32, drive of cars / delivery vans 1:32 and 1:24, locomotive drive track 0 and 1 for small vehicles also track 2, cable winches, anchor winches, chain drive, special functions.

 [ BUILDING INSTRUCTIONS - 283 Ko ]

These small power strips are very suitable as charging plugs to charge LIPOs that are built into models. The set consists of 1 x socket and 1 x plug. Pitch 1.27 mm.